|
|
Order:
888-257-4406
HomeTech Solutions
Cupertino CA
Cable Coax DSL HDMI IR Leviton Plate Quickport Speaker Splitter Switch Video Wall Wire
|
|
Nail Plate
- Clips instantly to metal or wood studs.
- Removable.
- Heavy gauge steel protects wires and pipes from sheetrock screws and nails.
- If your wires or pipes go through the stud less than 1.5" from the edge of the stud, according to code, you must install a nail-plate.
- If you drill a hole in a 2x4 stud larger than 3/4", you must use a nail plate on the sheetrock side(s) of the stud.
- 1 1/2" W x 3 1/8" H x 1" D
Hide
Loading real-time item data...
304B2
Bridle Ring, 1.25 inch, Wood Thread
CADDY Plain, Threaded and Wood Screw Bridle Rings for voice communication, signal, and control cable.
To support low-speed cable.
Hide
- When combined with other CADDY® Fasteners, Bridle Rings can be located on:
- Beam Flanges up to 3/4" - use with 2FMP28, BC, BC200, or M912
- Drop Wire - use with 4Z34 or 6Z34
- Concrete - use with 4TIB
- "C" Purlins - use with VF144TI
- "Z" Purlins - use with 1224TI or AF144TI
- Acoustical T-Grid - use with ATS4I or ATA4I
Loading real-time item data...
4BRT20WS
Cable Cat Cable Support
- Provides proper support of Category 5, fiber optic, and innerduct.
- Cost effective alternative to expensive cable tray.
- Complies with UL, cUL, NEC and EIA/TIA requirements for structured cabling systems.
- Suitable for air handling spaces (plenum).
- Holds up to 425 cables of 4-pair UTP or fiber optic cable.
- Load rated to 100 lbs.
- Adjustable 4" or 6" diameter loop.
- Perfect for holding all speedwrap cables together near headend panel.
Hide
Loading real-time item data...
CAT425
Cable Cat Cable Hanger Accessories
Angle brackets allow Caddy Cable Hangers (CAT12, CAT21, CAT32) to be mounted to a horizontal surface. There is a short hanger, a long hanger, and the machine screws that attach the CAT hanger to the angle bracket.
Hide
Loading real-time item data...
CATHBA S3575BP100 AFAB4
Low Voltage Cable Support
The CADDY® CATCR50 Cable Retainer is a plastic, low-voltage cable support with an easy-lock closure and an attachment base. The new cable retainer from ERICO® can be installed on walls, beams, studs, ceilings and racks - vertically or horizontally - which makes it extremely versatile. The CADDY CATCR50 support has rounded edges to avoid over-bending and kinking of cables. The patented closure on CADDY CATCR50 permits cable to be added quickly and easily. The locking teeth retain bundled cable in a one-piece support. The maximum cable capacity is 50 CAT 5e or 30 CAT 6 cables.
Hide
- Installs easily with nail, screw, push pin or pop rivet
- Works with CAT 5e and higher, fiberoptic and coaxial cable
- Allows for horizontal and vertical change of direction
- UL®-Listed
- Suitable for air-handling spaces (plenum rated)
- Complies with the NEC®, the CEC® and TIAsm standards
Loading real-time item data...
CATCR50
Cable Gripper
- Installs easily to metal and wood studs.
- Provides secure installation of multiple cables with unique locking/unlocking system.
- Staples, nails, or screws to wood studs.
- Attaches to existing holes in metal studs without tools.
- Supports four NMC or eight 4 pair UTP for DataCom (can not be combined).
- Delivers compliance with: NEC 300-4(d), CEC 12-510 and 12-516.
- Perfect for holding non-speedwrapped low-voltage cables in place inside walls.
Hide
Loading real-time item data...
CG4
Cable Support, Colorado Jim, Locking Tab
ERICO offers the CADDY "Colorado Jim" Cable Support - NEC Compliance for Metal Stud.
Can be used to support up to 6 runs of nonmetallic sheathed cable or up to 4 runs of MC and AC cable.
Hide
- Requires no special tools to install - only a hammer, nails or staple
- New easy-to-use locking tab
- Cable locating ribs to maintain cable separation
- Flared edges for cable protection
- Use self drilling and tapping screws on metal stud
- Delivers compliance for CEC Rule 12-510 on all studs, 12-618 for AC cable CJ6IN (only), CEC rule 12-516 for NMD wire on metal studs
Loading real-time item data...
CJ6
Hole Grommet, Easy Snap
ERICO offers the CADDY Metal Stud Punch and Easy Snap Grommet.
Hide
- Snap one grommet into standard 1-11/32" field punched hole OR snap two together into any shape factory punched hole
- Provides full 360° protection for cable and makes cable pulls easier
- ESGP can be used for 1/2" to 1": copper tubing
- Delivers compliance with NEC Article 300-4(b)(1) and CEC Rule 12-516
- Fits any size or shape metal stud hole
- NEW yellow color for better visibility
Loading real-time item data...
ESG1
Backless Mounting Bracket
- Use instead of wall-boxes in new construction.
- Simply screw or nail into wood or metal studs before the sheet-rock goes up.
- Built-in cable or PVC/Conduit holders.
- Can be mounted horizontally or vertically
Hide
Loading real-time item data...
MP1S MP2S
Plastic Cut-In Ring
- Easily add new low-voltage wall-plates.
- Installation requires only a pencil and sheet-rock saw.
- No sharp edges to cut or poke fingers or wires.
- New plastic design.
- Fastest and easiest way to put a low-voltage wallbox in an existing wall.
- Serrated interlocking system secures tight.
- For low voltage class 2 use only.
- Available in single-gang, double-gang, and a special 3 or 4 gang version (break it off in different ways to support 3 or 4 gangs.)
Hide
Loading real-time item data...
MP1P MPAL2 MP34P
Metal Cut-In Rings
- Easily add new low-voltage wall-plates.
- Use the cut-in ring as a template to trace the hole... Cut the hole in the sheet-rock... Put the cut-in ring in the hole and bend back the tabs... Then put in
- Then put in the (included) screws.
- You now have a place to screw the face-plate!
Hide
Loading real-time item data...
MPLS MPLS2
J Hooks
- Provides proper support of Category 5, fiber optic and innerduct cables.
- Variety of sizes and designs available to attach to virtually any structure.
- Cost effective alternative to expensive cable tray.
- Galvanized finish on J-hooks provide smoother cable pull and greater corrosion resistance.
- Complies with UL, cUL, NEC and EIA/TIA requirements for structured cabling systems.
- Holds up to 16 4-pair UTP or 2-strand fiber optic cables
- 3/4" diameter loop
- Include "bend back tab" to hold cables in place without additional tie-wraps.
- Complies with new TIA 569-A specification.
- Perfect for holding our speedwrap cable!
- Holds up to 50 4-pair UTP or 2-strand fiber optic cables
- 1 5/16" diameter loop
- Holds up to 5 runs of speedwrap cable!
- Holds up to 80 4-pair UTP or 2-strand fiber optic cables
- 2" diameter loop
- Holds up to 8 runs of speedwrap cable!
- Attach CAT cable support to bracket to hang cable up to 8" below rafters or floor joists.
- Attach CAT cable support to bracket to hang cable directly below rafters or floor joists.
- 1/4" - 20 x 3/8 Machine Screws
- Slot and phillips head
- Use to attach CAT12, CAT21, and CAT32 to CATHBA bracket.
Hide
Loading real-time item data...
CAT12 CAT21 CAT32
Camera Mounting Kit
- Provides positive wall support with locking screws (included)
- Mounts cameras on walls of 1/2" to 1-1/4" thickness
- Eliminates need for an electrical box when installing only low voltage Class 2 wiring
- Makes "fishing" cable easier
- Installs with drywall saw and screwdriver
- Complies with codes, standards, and best practices
Hide
Loading real-time item data...
SCMKW
|
HomeTech Solutions is UpFront