HomeTech Solutions' Logo
TechNews
New product info and special deals.
Bookmark and Share
Your Order
View Cart
Checkout
Status
Login
LEARNING CENTER
Knowledge Base
Incredible selection. Credible help.
HOME
NEW PRODUCTS
SPECIALS
MOST POPULAR
SUPPORT
Products Manufacturers
Drapery Control Gift Ideas Weather & Clocks Xantech Specials
Low Price Guarantee Icon
Order:
888-257-4406
HomeTech Solutions Cupertino CA
Map
Directions
Hours
Phone: 408-257-4406
Fax: 408-257-4389
Other Contact Info
Cable Coax DSL HDMI IR Leviton Plate Quickport Speaker Splitter Switch Video Wall Wire
Emitters
(10026)
Infrared Signal Emitters (Blinkers)

These devices are used to re-create the infrared signal from an electrical signal. Most of them are designed to stick to the front of a consumer electronics device and blink the IR signal directely into the device.


1552xC7
Infrared Emitter, Blink
  • Emitters blink in infrared as well as visible spectrum.
  • Available with one, two, or three emitter "heads" on a single 3.5mm (1/8") two conductor plug.
  • Single emitter has 7 foot cord.
  • Dual and triple emitters have 7 foot cord to the junction (round plastic disk), then 3 foot cord to each emitter.
  • Special purchase!
  • Limited time offer!
Hide
Loading real-time item data...

BBI15521C7 BBI15522C-7 BBI15523C-7

IR-300X
4 Pics
IR Emitters
These non-blinking infrared emitters output a very strong signal. Use them when you have low signal strength.
Hide
  • Blinks in the infrared spectrum only for maximum signal strength.
  • IR-3001: Clear adhesive film included on emitter housing for attachment
  • IR-3002: Small mounting clips stick to equipment. Emitters snap in and out of clips.
  • Unique design of dual emitter allows "unzipping" only as much emitter separation as your installation needs.
  • Spare adhesive film included.
Plug3.5mm Mono
Cord Length (Single)7 ft.
Cord Length (Dual)10 ft.
Loading real-time item data...

IR-3002 IR-3001

BBIR6
IR Blaster
  • Custom Made for Hometech
  • 6 Ft. Cord
  • Emmiter set at a 45 Deg angle
  • Made to sit under a component and blast IR to componet above
  • Dimensions: Length: 2 3/8 " Width: 3/8" Height at emmiter: 5/8" Height at lower section: 3/16"
Hide
Loading real-time item data...

BBIR6

282X
Naked, No shell Emitter
  • A 282M type high-output Mouse Emitter with no shell surrounding emitter head
  • Allows insertion of emitter inside component case for the cleanest appearance possible
  • Wire length: 10 feet
Hide
Loading real-time item data...

282X

IRPRISM
IR Prisim
The revolutionary and patented IRPrism is an Audioplex exclusive. This unique product is placed over the front of A/V component's IR sensors, will reflect incoming signals from your repeater system's emitters placed at the side, top or bottom of the units. IRPrisms attach directly to components via their self-adhesivestick pad. Get rid of unsightly emitter wires running across the front of high-end gear and improve off-axis remote control response in open cabinets with the IRPrism!
Hide
  • Allows IR from the front, side, top, or bottom to be detected by your components.
  • Use with IRFLOOD (above).
Loading real-time item data...

IRPRISM-10

28DES
2 Pics
Designer Emitter Shield
  • Effective for covering component IR eyes for IR
  • Shield cover for designer emitters
Hide
Loading real-time item data...

28DES

283D
Blink-IR Designer Emitter
  • Visible, red blink, low output version of the 282D.
  • Clear adhesive film for attachment to IR window of controlled component.
  • Includes 3 pre-cut adhesive backings for replacement purposes.
  • Lead is terminated with a 3.5mm mono mini plug.
  • Length of wire: 10 feet.
Hide
Loading real-time item data...

283D10P 283D 283D5P

282D
Standard High-Output Designer Emitter
  • Non-visible, high-output version
  • Deep purple LexanTM shell
  • Clear adhesive film included on emitter housing for attachment to IR window of controlled component
  • Includes 3 pre-cut adhesive backings for replacement purposes
  • Lead is terminated with a 3.5mm mono mini plug
  • Length of wire: 10 feet
Hide
Loading real-time item data...

282D10P 282D5P 282D

IRFLOOD
IR Flooding IR Emitter
Flooding IR Emitter simplifies systems where two or three components are placedin one shelf and can be flashed with the ultra-powerful IRFloods. Mount in front, above, below or on the side of the components, the IRFlood saturates each component in the shelf space.
Hide
  • Flooding IR Emitter
  • Includes double-stick tape.
  • 1/8" Male mono plug on 6' cable.
  • For best results, use IRPRISMs (below) on each component.
  • Also available in hard wired version
Loading real-time item data...

IR FLOOD PL IR FLOOD HW

286D
Blink-IR Dual Designer Emitter
  • Two emitters in series with each other and terminated in a single 3.5mm mono mini plug
  • Length of wire: 7 feet to junction, 3 feet to each emitter
Hide
Loading real-time item data...

286D 286D10P 286D5P

283TPD
Twin Plug Designer Blink Emitter
  • 283D Visible Designer Emitter with two 3.5mm plugs
  • Allows control of single source by two IR systems
  • Diode isolation for independent control and component protection
  • Wire length: 10 feet
Hide
Loading real-time item data...

283TPD

284D
Dual Designer Emitter
  • Two emitters in series with each other and terminated in a single 3.5mm mono mini plug
  • Length of wire: 7 feet to junction, 3 feet to each emitter
  • Non-visible, high output version
Hide
Loading real-time item data...

284D 284D5P 284D10P

282TPD
Twin Plug Designer Emitter (Non-Blink)
  • 282D high-output Designer Emitter with two 3.5mm plugs
  • Allows control of single source by two IR systems
  • Diode isolation for independent control and component protection
  • Wire length: 10 feet
Hide
Loading real-time item data...

282TPD

IRBUGPL
Adjustable IR Bug, plug-in
Have you ever been frustrated trying to set up a system and having the emitter overpower its intended target? Time spent trying to find the 'sweet spot' on a component not onbly costs you money, but can also make for unreliable infrared performance.

Audioplex has solved this signal strength problem with the introduction of the Adjustable IRBug*. By simply turning the adjustment screw, you can fine tune the signal strength of the emitter to perfectly match any component inyour system!

Available in both hard-wire and plug-in versions, you can now feel confident that you are always sending the perfect signal.
Hide
  • Connector: Screw-type, 2 wire
  • Mounting: IRBug: Directly to the front panel of each A/V component
  • Range: 10 -15 feet +,
  • Angle: +/-20-30 degrees off nominal axis. +/- 50-60 degres off axis.
  • Wire: Use conventional unshielded "zip" or telephone wire.
Loading real-time item data...

IRBUG-PL Adjust

47621-MIE
IR Emitter
Multi-Room Infrared (IR) Repeater System

The IR Repeater System consists of three pieces: an IR Target, IR Emitter and a distribution block for distributing control signals to multiple emitters. The IR Target takes the signal from a remote control for an audio/video component, such as a DVD player or home theater receiver, and converts it to a low-voltage electrical signal for use over long distances and in different rooms. The electrical signal is converted backat the component to be controlled by the IR emitter. With such a set-up, a usercan control a DVD player down in the family room from an upstairs bedroom, for example. The IR Repeater System is highly useful with multi-room audio/video distribution.

One IR Emitter is used for each controlled A/V component, through the distribution block in the Structured Media Enclosure. Distribution block (Cat. No. LE-47689B) available separately.
Hide
  • Features adhesive surface for easy installation on audio/video components.
  • Uses Catagory 5/5e UTP wire.
  • Cable length 6 foot.
Loading real-time item data...

47621-MIE

FILTER
Filter,Cable Clamp,35 OHM,7mm
Cylindrical Snap on filter.
Hide
Impedance 35 Ohm
Impedance 35 Ohm
Loading real-time item data...

445-2041-ND

IRBUGHW
Adjustable IR Bug, hard wire
Have you ever been frustrated trying to set up a system and having the emitter overpower its intended target? Time spent trying to find the 'sweet spot' on a component not onbly costs you money, but can also make for unreliable infrared performance.

Audioplex has solved this signal strength problem with the introduction of the Adjustable IRBug*. By simply turning the adjustment screw, you can fine tune the signal strength of the emitter to perfectly match any component inyour system!

Available in both hard-wire and plug-in versions, you can now feel confident that you are always sending the perfect signal.
Hide
  • Connector: Screw-type, 2 wire
  • Mounting: IRBug: Directly to the front panel of each A/V component
  • Range: 10 -15 feet +,
  • Angle: +/-20-30 degrees off nominal axis. +/- 50-60 degres off axis.
  • Wire: Use conventional unshielded "zip" or telephone wire.
Loading real-time item data...

IRBUG-HW Adjust

Graphic Element
Knowledge Base
Tutorials
Seminars
Books & Videos
FAQ Icon
KB Article
Follow us on Twitter
Follow us on Facebook
Our videos on YouTube
RSS Feed

In Business Since 1992 Icon Satisfaction Guarantee Icon Same Day Shipping Icon Privacy Policy Icon Low Price Guarantee Icon Tech Home Icon

site map | resale info | employment | contact us | SUPPORT
Text and images copyright © 1992-2010 HomeTech Solutions. All rights reserved.
[Thu 07/29/10 10:52:31 PM PDT] Tiny HomeTech Logo HomeTech Solutions is UpFront