Infrared Connecting Blocks

Multiple Zone Connecting Blocks
Four Zone Amplified Connecting Block
Six Zone Connecting Block/Expander
Two Zone Connecting Block

Related Links
Main Index
Infrared Index
Infrared Receivers
Infrared Emitters
Power Supplies
IR Distribution Accessories
Combination IR Receiver & Volume Control
IR Distribution Tutorial

• Connects one emitter port and power supply to Xantech IR receivers that use a stereo mini plug.
• Also includes a 3-terminal block for wired connection of Xantech IR receivers and Smart Pads.
• 3.5mm stereo mini jack for quick-connect IR receivers.
• 3.5mm mono mini jack for 1 single or 1 dual emitter.
• 2.1mm coaxial power jack.
• Uses either 781RG or P1216 power supply.
• Dimensions: 2 1/8" x 1-1/4" x 3/4".

• Multi-purpose 9-tap connecting block.
• High current design (12 Amps peak) allows amplifiers rated as high as 500 watts to be used with the CB18.
• One-in eight-out or eight-in one-out capability.
• Nine 4-terminal plug-in connectors on 4-conductor bus.
• Screw terminals handle wire sizes from 24 to 12 gauge.
• Dimensions: 11 1/4" x 1-1/4" x 1-1/4".

• Connects two emitter ports and power supply to Xantech IR receivers that use a stereo mini plug.
• 3.5mm stereo mini jack for quick-connect IR receivers.
• Two 3.5mm mono mini jacks with 470 ohm resistors drive 2 single or 2 dual emitters.
• 2.1mm coaxial power jack.
• Uses either 781RG or P1216 power supply.
• Dimensions: 2 1/8" x 1-1/4" x 3/4".

• Connects six emitter ports and power supply to all Xantech IR receivers that use a stereo mini plug.
• 3.5mm stereo mini jack for quick-connect IR receivers.
• 3.5mm mono mini ports drive 6 single or 6 dual emitters in parallel.
• Contains a series 100 ohm resistor per emitter port.
• 2.1mm coaxial power jack.
• Uses either 781RG or P1216 power supply.
• Dimensions: 3" x 1-3/4" x 13/16".

• Connects four emitter ports and power supply to all Xantech infrared receivers and key pads.
• Four parallel emitter ports with 470 ohm resistors drive 4 single or 4 dual emitters.
• Quick-connect stereo mini jack for Xantech IR Receivers that use a stereo mini plug.
• 2.1 mm coaxial power jack.
• Uses either 781RG or P1216 power supply.
• Includes 781RG power supply.
• Dimensions: 3" x 1-3/4" x 13/16".
• Note IRDY4Kit contains:
• 1X 78944 Connecting Block,
• 1X 781RG Power supply,
• 4X 283M Emitters
• AKA: 789-44 (The "PS" means that it includes a Power Supply.)

• Emitter expansion block for 79144, etc.
• Parallel emitter ports drive 10 single or 10 dual emitters.
• Contains a series 100 ohm resister per emitter port.
• Emitter & IN/OUT port are 3.5mm mono mini jacks.
• Screw terminals provide for wired input connections.
• Requires the 79144 amplified connecting block to drive the 79000 block.
• Dimensions: 6" x 2-1/4" x 15/16".

• Amplified version of the 79000.
• Emitter ports with jumpers permit high or low power.
• High-speed opto-isolator for improved operation.
• Quick-connect stereo mini jack for Xantech IR receivers that use a stereo mini plug.
• Parallel emitter ports drive 10 single or 10 dual emitters.
• Up to nine 79000's can be connected to the 79144 if more than 10 emitter ports are needed.
• Contains red LED input signal Test-IR.
• Note IRDY10Kit contains:
• 1X 79144 Connecting Block,
• 1X 781RG Power supply,
• 10X 283M Emitters
• Uses either the 781RG or P1216 power supply.
• Dimensions: 6" x 2-1/4" x 15/16".
• Note IRDY10Kit contains: 1X 79144 Connecting Block, 1X 781RG Power supply, 10X 283M Emitters

• Power booster and/or phantom power modes.
• Phantom mode powers the 29110, 48000, 49000, and 78010 series IR receivers for 2-wire operation.
• Low current mode drives up to 4 emitters in series.
• High current mode drives 790 connecting block.
• 3.5mm mono mini jack emitter port.
• Uses the 781RG power supply.
• Dimensions: 4-1/4" x 1-5/8" x 1".

• Controls 4 individual zone's equipment.
• Can control 2 pieces of equipment per zone.
• Controls 10 pieces of equipment used for common sources.
• Expandable to 9 zones with 79620.
• 14 test LED's indicate proper operation and hook-up.
• Uses 28200, 28300, 28400, or 28600 emitters.
• Maximum current output: 100mA. Requires 781RG or P1216 Power Supply.
• Inputs: Four 3-screw terminal connectors to interface with all Xantech IR receivers and Smart Pads.
• Outputs: 8 zone emitter ports and 10 common emitter ports (3.5 mm mono mini jacks).
• Dimensions: 1" x 13-3/8" x 1-7/8"
• Expandable to 9 zones with 79620 .

• Expands the 795 Zone Controller to a total of 9 zones.
• Connects directly to the 795 and is powered by the 795.
• May be used in conjunction with a 79144 (without a 795) for a 6 zone system.
• Multiple 796's may be used with a 79144 for even more zones (limited only by IR noise considerations.)

• Simplified version of 795 controller when only two zones are required.
• One plug-in screw connectors for each zone's IR receiver and/or keypads.
• One 3.5 mm mono mini jack output for each zone's IR emitter control.
• One 3.5 mm mono mini jack output for common IR emitter control.
• Can be used with a 79144 amplified connecting block for common emitter expansion.
• 2.1 mm coaxial power jack for connection of 781RG or P1216 Power supplies.
• Dimensions: 3" x 1-3/4" x 13/16".

• Multi-zone capable.
• IR Receivers can be connected to screw terminals or mini-jack.
• Two common (global) IR outputs.
• Two zone IR outputs
• Expandable, jumper included
• Use with C1201 to simplify connecting multiple IR receivers.
• Compatible with IR equipment from most manufacturers.
• Includes power supply
• Powers up to 16 IR receivers.
• Channel Vision IR Connecting Block
• Powers up to 16 IR receivers.
• Multi-zone capable.
• IR Receivers can be connected to screw terminals or mini-jack.
• Two common (global) IR outputs.
• Two zone IR outputs
• Expandable, jumper included
• Use with C1201 to simplify connecting multiple IR receivers.
• Compatible with IR equipment from most manufacturers.

	Instruction Manual
	Instruction Manual
	Instruction Manual

• Simple IR Hub
• Connect one IR-receiver to one emitter
• Power supply included

	Instructions
	Instructions