Relays & Switches
68610
Remote Speaker Switcher
|
|---|
|
|---|
- 200 watts per channel capacity.
- Switchable 4-ohm series resistor for amplifier protection.
- Isolated Left and Right Grounds.
Allows use of Bridging type power amplifiers.
- 4-terminal IR input for Xantech IR receivers, Smart Pads
and other devices.
- Programming and ID code switches permit Toggle, Pair and
Group mode settings as well as different IR codes for use of
multiple 686's in the same system.
- Universal mounting fits 19-inch racks or any 3 1/2x19 surface.
Projects about 2 3/4 inches behind panel with cables connected.
- Requires RC68 Programmer and 78200 Power Supply.
|
|
The 686 is a stand alone switcher that allows the installer and user to turn six pairs of speakers ON and OFF by way of infrared commands. A particular room may be given the ability to trunk only its own speakers on or off. Another room, such as the main control room, may be given control of the entire house in a "party mode". The 686 does not require a 670 Smart Switch Controller.
| |
|
SR21
Remote A/B Speaker Relay Module | 
|
|---|
- Stand alone remote controlled A/B speaker switcher.
- Connects one amplifier to 'A' or 'B' speaker pair.
- Connects one speaker pair to either an 'A' or 'B'
amplifier.
- 5 amp/30VDC current rated relay.
- IR input terminal.
- IR code select switch.
- LED indicates A or B status.
- Requires RC68 Programmer IR codes for operation.
- Requires 781RG power supply.
- Dimensions: 5 1/4" x 2 3/8" x 1 7/8".
|
|
|
CC12
1 Channel Remote Relay Module | 
|
|---|
- Provides "dry contact" closures for a multitude of uses.
- One double pole, double throw relay, 5 amp/30VDC rated.
- 4 contacts available: 2 normally open, 2 normally closed.
- LED indicates contact status.
- IR input terminal.
- IR code select switch.
- Requires RC68 programmer IR codes for operation.
- Also voltage switchable at C1 terminal.
- Requires 12VDC 300mA power supply.
- Dimensions: 5 1/4" x 2 3/8" x 1 7/8".
|
|
|
Xantech
CC62
6 Channel Remote Relay Module |
|
|---|
- 6 double-pole double-throw relays, 5 amps, 30 VDC rated.
- 2 normally open and 2 normally closed contacts per relay.
- Six 6-terminal screw-type plug-in connectors - one for each of the relays.
- Requires RC68+ Programmer and 12VDC 1.0A Power Supply.
- Dimensions: 19”W x 3 1/2” H x 2 1/4” D (483mm x 89mm x 58mm)
- Instruction Manual (PDF)
| |
|
Xantech
IRS232A
IR to RS232 Converter |
|
|---|
- Requires Dragon Drop-IR™ for programming.
- Converts Xantech RC68+ IR codes to ASCII commands.
- Requires 12VDC 300mA power supply and RC68+ Programmer.
- Instruction Manual (PDF)
| |
IRS232 Module provides IR control of advanced components such as projectors and lighting systems that would normally be controlled via RS232 with exotic controllers or automated systems.
| |
|
Xantech
IR-X10
IR to X-10 Converter |
|
|---|
- Converts specific Dragon Drop-IR codes into X10 control signals
- IR input accepts Xantech IR bus output from any of the Xantech IR receivers, keypads, connecting blocks or controllers
- X10 RJ11 output jack connects to the X10 Power Line Interface Module using the included RJ11-to-RJ11 cable
- Requires a 12VDC 300mA Power Supply and Dragon Drop-IR programming software
- Requires X10 TW523.
- Instruction Manual (PDF)
| |
|
|
