UPB Signal Couplers & Amplifiers
PPC1
UPB Passive Phase Coupler |
|
- Assure reliable UPB signal strength.
- Simple two-wire connection.
- Connects across both legs of 220V split-phase residential service.
|
| Note: PCS strongly suggests professional installation of their UPB products.
|
39A001
UPB Passive Phase Coupler |
|
- Assure reliable UPB signal strength.
- Simple two-wire connection.
- Connects across both legs of 220V split-phase residential service.
-
Installation Instructions(PDF)
|
| UPB™ is for single phase 120/240 VAC, 60 Hz systems. The HLC Phase Coupler mounts by the circuit breaker box and is used to connect the signal from L1 to L2 within the circuit breaker box.
A Phase Coupler is a strongly recommended component of an HLC System. Its use increases the reliability of the UPB™ signal.
The LED on the Phase Coupler shows that it is working.
| |
|
ZPCI-W
ZPCI-B
UPB Inverting Phase Coupler |
![]()
![]()
![]()
|
- Operating Voltage: 2-phase, 120VAC+/- 10% per phase
- Voltage Supression: 500V L-N 900V L-L
- Peak Voltage Current: 27,000A per phase
- Operating Temperature: -40 - +50°C
- ZPCI-W
- Dimensions: 4.10"Hx1.75"Wx1.44”D (104 x 45 x 37mm)
- Weight: 3.8oz (108g)
- Mounting: standard juntion box
- ZPCI-B
- Dimensions: 3.67"Hx1.97"Wx2.58”D (93 x 50 x 66mm)
- Weight: 7oz (184g)
- Mounting: breaker box
- Compatibility:
Cutler-Hammer
Square D (Home-Line)
Murray
GE
-
Data Sheet(PDF)
-
Installation Instructions(PDF)
|
| When installed inconjunction withUniversal Powerline Bus (UPB) home automation products, Universal Inverting Phase Couplers make a highly reliable system even better.
Besides UPB signals, these Universal Phase Couplers also pass X10 and broadband frequencies, and thus are able to address mixed technology applications with only one device per home.
Model ZPC Universal Inverting Phase Couplers are designed with LEDs that indicate proper connection and operation.
Model ZPCI-W — Wire-in Universal Inverting Phase Coupler is designed for mounting inside a junction box
Model ZPCI-B — Breaker-box Mount Universal Inverting Phase Coupler is designed to be mounted inside most standard power centers that have available space for a 220V circuit breaker.
| |
|
ZPCI-P30A
UPB 30A Plug-in Inverting Phase Coupler |
![]()
![]()
![]()
|
- Same specifications as ZPCI above.
- Built-into a 30 amp "dryer" plug and socket.
- Simply unplug your dryer, plug in this coupler, then plug the dryer into the coupler. Instant couper installation!
-
Data Sheet(PDF)
-
Installation Instructions(PDF)
|
|
|
ZPCI-P50A
UPB 50A Plug-in Inverting Phase Coupler |
![]()
![]()
![]()
|
- Same specifications as ZPCI above.
- Built-into a 50 amp "dryer" plug and socket.
- Simply unplug your dryer, plug in this coupler, then plug the dryer into the coupler. Instant couper installation!
-
Data Sheet(PDF)
-
Installation Instructions(PDF)
|
|
|
|
Bridge helps assure sufficient signal strength throughout 3-wire systems. The Signal Bridge coupler the command signal onto the 120V legs of the power system to ensure sufficient command signal strength throughout the command network. Use of the 6299 is recommended for all installations. The wiring diagram shows the proper method for coupling a typical residential 120/240V system. When used in the same DHC network as a 6201 system Amplifier, the 6299 Signal Bridge should NOT be in the same panel or within 10 feet of the 6201. Dimension of 6299 is 2.693" x 4.125" x 1.387".
This device may be wired on the LOAD side of any DHC Switch or Dimming Module (except 6381 or 6383), or on the LINE side of any fixture using an electronic ballast, a low-voltage ballast, or any noise generating source. The 6287 prevents interference generated by fixture components fixture components from interfering with DHC signals. Dimensions of 6287 are 1.578" x 1.850" x 0.75".
The 6289 Noise Reducer filters electrical "noise" and signals with frequencies above and below the 121 kHz signal. The 6289 may be installed at the noise or signal source or at the module affected by the interference. Depending on the source of the interference, the 6289 may be wired phase to neutral or phase to phase. Dimensions of 6289 are 1.168" x 2.600".