Speaker Drivers
120
Multi-Channel Recordable Voice and Siren Driver Module |
|
|---|
- Four Channels Configurable as: Two Siren and Two Recordable Voice OR Four Recordable Voice
- Maximum record time is 8 minutes divided between the number of voice channels.
- Siren Sounds: Classic Yelp Siren, Temporal Coded Horn, and Steady Industrial Horn
- Temporal Coded Horn meets ANSI standard for Audible Emergency Evacuation Signaling
- Recordings stored in non-volatile memory
- Voice channels accept momentary triggers
- "One Shot" or Continuous voice playback settings
- Option to trigger +V1 and or +S3 channels from a steady or pulsing input (ComboTrigger™)
- Built-in condenser microphone for recording
- Adjustable speaker volume and current draw
- Powerful 24 watt audio amplifier for Speakers
- Line Level Output Jack for Paging Systems and Amplifiers
- PC sound card interface connector
- Lifetime Limited Warranty
- Operating Voltage: 11 to 14 Volts DC
- Current Draw: .2 to 2 Amps, (depends on volume setting & speaker load)
- Sound Level: 120 db @ 1 meter, 14 vdc, with one 8 ohm speaker
- Max. Speaker Loading: 4 Ohms
- Pulsing Input: 1/2 to 2 Second Pulse, 50% duty cycle
- Size: 3" x 5" x 1.25" (76 x 127 x 32mm)
- User's Manual (PDF)
| |
The ELK-120 v.2 features 4 channels that can be configured as 2 channels of siren and 2 channels of voice, or all 4 channels can be used for voice. Either way the voice channels are fully recordable and are stored in non-volatile re-programmable memory. Total time of recording is 8 minutes. The Siren channels offer a choice of: Classic Yelp Sound, Temporal Coded Horn, or Pulsing Industrial Horn.
| |
|
129
Computer Sound Card Interface |
|
|---|
- Powers ELK-120 or ELK-124 Modules during Programming
- Power Switch
- Audio Jacks for Computer and Speakers
- Plug-In Cable for Quick Connections to Recordable Modules
- Includes 6 foot Shielded Cable for Speakers
- Compact Plastic Case
- Programs Recordable Modules in Seconds
- Lifetime Limited Warranty
- Size: 4.4" x 3" x 1.15" (111.8mm x 76.3mm x 29.2mm).
- Supplies 12Volts D.C. @ 1 Amp for ELK-120 / 124 Modules
- Requires Windows 3.1 or higher, 386 processor or better, 4MB RAM, 2MB Hard Drive Space, 3 ˝” Floppy Drive, Stereo Speaker Output Jack or Sound Card and computer speakers
- Requires (1) 12V, 20VA AC Transformer (not included) to program the ELK-120 or ELK-124
- User's Manual (PDF)
| |
The ELK-129 Computer Sound Card Interface allows a computer’s speaker output to be used as one of the tools for programming the ELK Recordable Modules, such as the ELK-120, ELK-124, or ELK-MV480. The included shareware software is used to process your computer’s audio files for use with the ELK-129. The ELK-129 then "downloads" the processed files to the Recordable Module. Finished messages can be saved on your computers hard drive for re-use.
| |
|
ELK-800
10 Watt Audio Amplifier |
|
|---|
- 10 Watt Amplifier
- Expanded Telephone System Paging
- Does Not Require 25 or 70V Line Transformers
- Multiple Speaker Hookups
- Requires only 22-24 gauge telco wire
- Built-in Volume Control & Gain Select
- Compact Size
- Surface Mount ABS Enclosure with Snap-On Cover
- Lifetime Limited Warranty
- Operating Voltage: 12 to 24 Volts AC or DC
- Current Draw: 38 - 800 mA, Depending on Load and Volume Setting
- Rated Output: 10 Watts
- Output Speaker Load: 2 to 16 Ohms
- Input Impedance: 1000 Ohms Nominal
- Audio Input Level: 15 dBm to +10 dBm
- Enclosure Size: 4.4" x 3" x 1.15" (111.8mm x 76.3mm x 29.2mm)
- User's Manual (PDF)
| |
The ELK-800 is a great compact audio amplifier It may be connected to virtually any audio source, i.e. microphone, radio, computer sound card, telephone system paging output, etc., even an ordinary single line phone set. The audio source is amplified up to 10 watts, adjustable from an on-board volume control. Remotely installed, it saves money by requiring only 22 - 24 gauge telco or alarm type wire. It operates on 12 -24 volts AC or DC and has built in volume adjust. It can also drive multiple speakers.
| |
|
ELK-110
Voice/Siren Driver Module |
|
|---|
- Installer Friendly - Compact & Easy to Mount
- Two Input Channels, Burglar & Fire
- Bilingual Voice - English and or Spanish, Siren Only, Speech Only, or Combined
- MilliMiser™ Lowers Current Draw
- ComboTrigger™ For Single Outputs
- VolumeStep™ Slowly Increases Siren Volume
- Temporal Coded Fire Signal
- Pre-Wired For Easy Installation
- Lifetime Limited Warranty
- Operating Voltage: 10 to 14 Volts DC
- Current Draw: 1.25 Amps, (800 mA on MilliMiser™ setting), with one 8 Ohm speaker
- Sound Level: 120 db @ 1 meter, 14 vdc, with one 8 Ohm speaker
- Max. Speaker Load: 4 Ohms
- Size: 2.75" x 4.0" (70mm x 102mm
- User's Manual (PDF)
| |
The ELK-110 Voice "Talking" Driver features high quality digitally pre-recorded voice messages and loud attention getting siren sounds in an economical, low current draw, compact package. It features two input channels, bilingual voices (English and Spanish), and many unique options which allow it to be used with virtually any residential or commercial alarm installation. The voice messages and the siren alternately sound whenever one of the channels are activated.
The ELK-110 may be customized by use of on-board jumpers. For example: our MilliMiser™ option allows the already low current draw of the ELK-110 to be reduced even lower. This is ideal for controls with limited alarm output power. The ComboTrigger™ option allows controls which have a single alarm output and pulsing option to activate both the burglar and fire alarm sounds. The VolumeStep™ option is best described as the "peacekeeper", since it causes the siren sound to start at low volume, gradually increasing over 90 seconds to maximum volume.
| |
|
|
The ELK-1RT is a rugged 30 Watt, 8 Ohm speaker mounted in a tamper resistant, "No Rust" enclosure. It features two sealed reed tamper switches, one on the Back plate and one on the Front Cover. The stainless steel naturally reflects the mounting surface and blends easily with any residential or commercial building.
The ELK-73 is a 20 Watt, 8 Ohm Speaker mounted in an attractive surface mount plastic enclosure. This versatile Echo™ Series speaker is designed to be heard but not seen!. Sound "echoes" off mounting surface from back plate edge.
The ELK-150RT is a self-contained Siren in a tampered "No Rust" stainless steel enclosure. It features two sealed reed tamper switches, one on the Back plate and one on the Front Cover. The switches are normally closed and pre-wired in series. The ELK-150RT can produce two distinct sounds from a single input trigger. The stainless steel exterior reflects the color of the mounting surface allowing the ELK-150RT to blend easily with any residential or commercial building.
