Weatherproof Enclosures
HomeTech Solutions
|
|---|
|
|
684RTSCE
Raintight Enclosures |
16" x 24" x 8"
6" x 8" x 4"
8" x 12" x 6"
|
|---|
- Raintight Removable Screw Cover
- Nema type 3R
- Heavy-Duty 16 Gauge Construction
- High-gloss Gray Baked Enamel
| |
Designed for use as wiring boxes and junction boxes in outdoor installations. Rainproof enclosures will protect the enclosed equipment against rain, sleet, and snow. Rainproof may be used indoors where dripping water is a problem.
| |
|
HomeTech Solutions
|
|---|
|
|
WUX1417
Raintight Vertical Shanty |
View opened box
|
|---|
- Backless Enclosure
- Raintight Hinged Housing
- Nema type 3R
- Heavy-Duty 16 Gauge Construction
- High-gloss Gray Baked Enamel
- 14" Wide x 17" High x 2" Deep
| |
Outdoor semi-flush housing designed to protect indoor surface devices mounted on exterior walls.
For new construction. Mount this box to the bare sheathing (plywood, particle board, etc.) before siding or stucco. The box is only 2" deep, so most installers cut out the sheathing in the box, giving access to the stud bay inside the wall. (Be sure to check local building codes before doing this because you may be breaking the vapor barrier.) If the other side of the wall (which is now the back of the box) is sheetrock, you can glue a piece of plywood to the back of the opening with construction glue.
| |
|
HomeTech Solutions
|
|---|
|
|
WG 1020-025
|
Bigger Picture (Opened)
Bigger Picture (Closed)
|
|---|
- Wood-Backed Enclosure
- Raintight Hinged Housing
- Heavy-Duty 16 Gauge Construction
- Two Hex-Head Latches
- Padlockable Quick-Latch
- Cross-Reference number: BN 5130 W
- Hinged Cover
- Embossed "Telephone" on cover
- Poly-Urethane Power Coat Baked Beige
- Open top and bottom behind flange simplifies wiring.
- Sturdy plywood back.
- UL Listed.
- 14.5" Wide (not including flange) x 25" High (not including flange) x 6" Deep
- Recessed depth behind flange: 4.5"
| |
Outdoor semi-flush housing designed to protect indoor surface devices mounted on exterior walls.
For new construction. Mount this box to the bare sheathing (plywood, particle board, etc.) before siding or stucco. The box is 4.5" deep behind the flange so it will only fit in a thicker-than-usual wall, or where the box can protrude through the other side of the wall. Open top and bottom allows very easy wire installation. Plenty of room inside to mount RF, Satellite, and Telephone distribution products.
| |
|
HomeTech Solutions
|
|---|
|
|
WG 1100-20
WG 1100-15
|
Bigger Picture (Opened)
Bigger Picture (Closed)
|
|---|
- Wood-Backed Enclosure
- Raintight Hinged Housing
- Heavy-Duty 16 Gauge Construction
- Two Hex-Head Latches
- Padlockable Quick-Latch
- Hinged Cover
- Embossed "Telephone" on cover
- Poly-Urethane Power Coat Baked Beige
- Open top and bottom behind flange simplifies wiring.
- Sturdy plywood back.
- UL Listed.
- 14.25" Wide (not including flange) x 4.75" Deep
- Height varies (see item listing) and does not include flange
- Recessed depth behind flange: 3 1/8"
| |
Outdoor semi-flush housing designed to protect indoor surface devices mounted on exterior walls.
For new construction. Mount one of these boxes to the bare sheathing (plywood, particle board, etc.) before siding or stucco. These boxes are only 3 1/8" deep behind the flange so it will fit in a normal wall. Open top and bottom allows very easy wire installation. Plenty of room inside to mount RF, Satellite, and Telephone distribution products.
| |
|
RJ Series
Raised Cover Enclosure |
|
|---|
- Compression molded fiberglass & reinforced polyester construction.
- Memory retaining, continuous silicone door gasket.
- Stainless steel padlock hasp.
- Integral mounting feet.
- Molded in panel mounting inserts.
- Machine tool gray.
- Marine-grade aluminum back panels are available.
|
These weatherproof enclosures are designed for use as instrumentation housing, terminal wiring boxes or electrical control enclosures. The RJ series is ideal when additional depth is required for specific instrumentation and components.
| |
| |
JxxxxHPL
J Series Enclosures |
|
|---|
Features- Compression molded fiberglass & reinforced polyester construction.
- Memory retaining, continuous silicone door gasket.
- Integral mounting feet.
- Molded in panel mounting inserts.
- Machine tool gray.
- Marine-grade aluminum back panels are available.
- Padlock latch for quick entry
- Snap catch concept with toggle action
- Full 180°+ door opening
Additional Documents
|
|
These weatherproof enclosures are designed for use as instrumentation housing, terminal wiring boxes or electrical control enclosures.
|
|
|
JxxxxPVC
PVC Series |
|
|---|
Features- Lighter and less expensive than its fiberglass counterpart.
- On-the-job impact and abrasion resistance.
- PVC construction makes modifications simple.
- All-purpose enclosures for amplifiers, splitters and head-end equipment.
- PVC is naturally UV resistant.
- No sidewall obstructions
- Made from water resistant PVC and PVC gaskets
- Cost effective to general purpose application Instrument Sized Enclosures.
|
|
These weatherproof enclosures are the first choice when affordability is a primary concern. PVC construction makes them easy to modify to fit your specific needs. These can be used for just about any application. From RF Amplifiers to DSS Multiswitches, PVC enclosures offer reliable protection at affordable cost.
|
|
|
HomeTech Solutions
|
|---|
|
|
CTWB33MB
Gray Wallmount Enclosure
|
![]()
![]()
![]()
|
|---|
- 2 1/2"H x 3"W x 1 3/4"D
- Weatherproof
- Location for tamper ring or tie-wrap to keep closed.
- Just large enough to crimp a few wires together.
|
| |
HomeTech Solutions
|
|---|
|
|
10MTEGYS
Gray Wallmount Enclosure
|
![]()
![]()
![]()
|
|---|
- 7 1/2"H x 5"W x 1 1/2"D
- Marked "CATV" on cover.
- Includes standard and security screws
- Includes mounting screws
- Lockable.
| |
|
HomeTech Solutions
|
|---|
|
|
11CTEGYS
Gray Wallmount Enclosure |
Pic1 Pic2
|
|---|
- 9x9x3 wallmount enclosure
| |
|
HomeTech Solutions
|
|---|
|
|
11MDEGYS
Large Outdoor Cable Demark Box, Gray |
Inside View
|
|---|
- Use as a full antenna/cable TV/satellite distribution enclosure (holds amps, splitters, multiswitch, etc.)
- Outside dimensions (including hinges and tabs): 12"(W) x 18 1/4"(H) x 3 3/4"(D)
- Usable Inside Dimensions: 10"(W) x 17"(H) x 2"(D)
- May be surface mounted or sunk up to 2-1/2" into wall.
- 2 compartments. Both independently lockable.
- Weather-tight.
- Universal feed-throughs in rear plate and bottom allow many wire dressing options.
| |
Need to do your video distribution outside the house? Use this enclosure to hide it all away from tampering and the elements.
| |
|
|
(BW315 shown.)
