Antenna Masts & Mounts

Steren Electronics, LLC. 200-603 Antenna Rotator with Infrared Remote
12 Channel Programmable Memory Non-Volatile Memory – Holds Locations During Power Failures Automatic Synchronization Ensures Pinpoint Position Accuracy Heavy-Duty Rotator Motor and Wind-Tested Brake Pads Precision-Cut Gear System with Built-In Steel Thrust Bearings Suitable for 1 1/2" - 1 3/4" Masts Motor Torque 160lb-in 1-RPM Maximum Vertical Load 100-lbs Power Source 117VAC 60Hz 62W Includes mounting hardware and remote control Controller 7" (W) x 2 3/8" (H) x 5 3/4" (D) Rotator 6 1/2"(W) x 11 1/2" (H) x 3 1/2" (D) 3 Conductor rotor cable available separately below.
ST-200603 Antenna Rotator,System,RemCtl For ordering information, please see this item on our current website.   HT-203 20 AWG, 3 Conductor, Stranded. Antenna Rotator Cable For ordering information, please see this item on our current website.

HomeTech Solutions MAST5 5 Foot Mast, 1 1/4 in., 18 gauge
5 Foot Length. 18 Gauge. Use two masts for 10 foot length. Keyed ends allow extending without twisting. Galvanized steel with grey powercoat.
GC-MAST5 5 Foot Mast, 18AWG Galvanized 1 1/4in. od. For ordering information, please see this item on our current website.

Nello Corporation Authorized Seller Click To Verify 100495 6 Foot Mast, 2 in. OD, 18 gauge
6 Foot Length. 18 Gauge. Galvanized steel. This 2" mast is the right size for mounting the new AT9 DirecTV dish! Note that you must use other mounting hardware (tripod, chimney mount, wall mount, etc.) that is compatible with a 2" mast. These masts do not fit together.
NO-100495 2in OD x 18 Ga 6ft Tubing Tubing For ordering information, please see this item on our current website.

HomeTech Solutions WALLMNT4 Mast Wall Mount, Heavy Duty	Mast Not Included Models May Vary
Accepts up to 1 1/4. masts. Holds mast 2 1/2" away from wall. Furthest protrusion with 1 1/4" mast approx 5". All zinc coated or galvanized steel hardware. Includes hardware. Sold in pairs.
GC-WALLMNT4 Wall Mount, 4 inch., Pair For ordering information, please see this item on our current website.

HomeTech Solutions WALLMNT12 WALLMNT18 Mast Wall Mount, 12 & 18 inch, w/support	Mast Not Included Model May Vary Slightly
Accepts up to 1 1/2 in. masts. Holds mast 12" or 18" away from wall. Support bar holds weight of mast. All zinc coated or galvanized steel hardware. Includes carriage bolts and lag screws. Sold in pairs.
GC-WALLMNT12 Wall Mount W/Supp, 12 in, pair For ordering information, please see this item on our current website.   GC-WALLMNT18 Dbl Wall Mount Kit 18 in. Fits 1.25in to 1.75in OD mast For ordering information, please see this item on our current website.

See also Satellite Dish Mounts

HomeTech Solutions CHIMMNT Chimney Mount w/18' Straps
Accepts up to 1 1/2 in. masts. Holds mast securely in two positions. All zinc coated, galvanized steel, or stainless steel hardware. Includes all hardware except mast. New version with simplified installation and instructions! Positive anti-turn feature.
GC-CHIMMNT Chimney Mount for Mast Y-Type, 18ft Straps For ordering information, please see this item on our current website.

Nello Corporation Authorized Seller Click To Verify 103489 Non-Penetrating FRM Roof Mount
34 3/4" square base 60" Mast, 1.25" O.D. included Ships dissasembled Does not fit the A49S 5 LNB Antenna Assembly diagram (PDF)
NO-103489 Non-Penetrating Roof Mount w/mast For ordering information, please see this item on our current website.

Non-Penetrating Roof Mount
DS5046 Non-Penetrating Frame Holds up to 6 concrete blocks. Use with DS5146 or DS5001 below. Galvanized. Grey powercoated.
DS5146 Large Mount Pipe Use with a 5' mast and a small antenna such as the TV50 and TV50MAST adapter. Or mount a DSS dish directly to the mount pipe. Use with one DS5046 frame and 6 concrete blocks or sandbags. Holds up to a 76cm antenna. 1 1/2" ID pipe. 19" Tall. Galvanized. Grey powercoated.
DS5001 Large Mount Pipe For large antennas and/or tall (up to 10') masts. Use with two DS5046 frames and 12 concrete blocks or sandbags. Holds up to a 1 meter antenna. 2 1/8" ID pipe. 2 3/8" OD. 30" Tall. Galvanized. Grey powercoated.
GC-DS5046 Non-Penetrating Roof Mount For ordering information, please see this item on our current website.   GC-DS5146 Roof Mount Post Kit For ordering information, please see this item on our current website.   GC-DS5001 Roof Mount Post Kit For ordering information, please see this item on our current website.

HomeTech Solutions TRIPOD3 TRIPOD5 Tripod Mast Mounts
Accepts up to 1 3/4 in. masts. 1 1/4" diameter legs. Holds mast securely in two positions. All zinc coated, galvanized steel, or stainless steel hardware. Preassembled. Does not include mast. 3 feet high (TRIPOD3) 5 feet high (TRIPOD5)
GC-TRIPOD3 Tripod, 3 foot For ordering information, please see this item on our current website.   GC-TRIPOD5 Tripod, 5 foot can fit 1 1/2in Vendor #811 For ordering information, please see this item on our current website.

HomeTech Solutions TRIPOD3A TRIPOD3AH TRIPOD5A Heavy-Duty Tripod Mast Mounts
Accepts up to 2 1/4 in. masts. All Heavy 5/16" Bolted Construction Easy to tilt and service Can be removed without leaving holes in roof Lessens chance of roof leaks Sturdier - Safer Replacement feet kits & tar pad kits available Holds mast securely in two positions. All zinc coated, galvanized steel, or stainless steel hardware. Preassembled. Does not include mast. 3 feet high (TRIPOD3A) 5 feet high (TRIPOD5A)
GC-TRIPOD3A Tripod, 3 foot, 2 1/4 in. mast For ordering information, please see this item on our current website.   GC-TRIPOD3AH Tripod, 3 foot, 2 1/4 in. mast Super Heavy Duty For ordering information, please see this item on our current website.   GC-TRIPOD5A Tripod, 5 foot, 2 1/2 in. mast Vendor #911 For ordering information, please see this item on our current website.